![]() Step 3 is the second reboot of the NAS:ġ1. During this step your NAS will reboot:ġ0. ![]() Click on Continue and you will see step 1 of the update start. Type should be Update and future version should be higher then current version.Ĩ. Verify the version information is correct. If you have more than one LaCie network storage device on your network, select your product from the list on the left. You will be asked for the update capsule file:Ħ. You will be asked to enter the administrator username and password:ĥ. Select your product and verify the current system version is less then 1.2.5:Ĥ. Connect and switch on your NAS, it should appear in the LaCie Network Assistant. Download the update from LaCie and save it to a location that is easily found.ģ. If it is not download and install the latest version.Ģ. Check that the LaCie Network Assistant version is 1.4.2 or later. Once the above conditions have been met proceed with the update below:ġ. Utilizzo della modalità di ripristino LNA. Download the 1.4.2 (or newer) version and install it. Uninstall all previous versions of LNA on your computer.Drag and drop or copy and paste files to your user folder. Do not use a direct connection from the network device to your Mac or PC. When prompted, enter the login and password for your user folder. ![]() These can be re-enabled after, but may interfere with the Network Assistant applying the update during. Turn off all firewall restrictions on the computer applying the update.Reset to default: See Update Product Operating System. Disconnect all shares on the NetworkSpace 2 from every machine connected to it Wake on LAN function in LaCie Network Assistant (see Wake on LAN) (see also Dashboard - Eco Management).From LaCie support, buying an official HDD replacement hardware while bring you the system as well. Without any system on any HDD, there is nothing to reset. If none, look in Device Manager for any yellow icons or something 'Lacie' in the sections of Disk Drives. As this isnt often used by computer users, many firewall and security programs will interfere with it. As one of LaCies troubleshooting pages admits: IP Configurator and Network Assistant software use a less common protocol called ARP to find an Ethernet Disk. Look for any message about new or unidentified devices. Installing a network drive is tough, software-wise. Turn off all other LaCie network devices on your network (please note that this is not required but prevents updating the wrong device) As far as I know, the reset sequence only reset some config files. If the problem is a missing driver, do the following : Connect the Cloudbox to only the PC, re-power it up completely (apparently needs 3-9 minutes), then reboot the PC.Make sure that users on your network have stopped any transfers to the NAS.Make sure both the network drive and the PC or Mac are connected via an ethernet cable. Do not use a wifi connection to apply this update. ![]() Typical transfer rate in wired Gigabit Ethernet network can be up to 35MB/s.Update Network 2 Drives using the LaCie Network Assistantīefore updating the firmware on your network drive make sure the following conditions have been met: ***Transfer rates depend on file sizes and formats, LAN configuration and other factors. Total accessible capacity varies depending upon operating environment (typically 10-15% less). LaCie Backup Assistant software with data restore for Mac® OS X 10.5, 10.6, 10.7 LaCie Backup Assistant software with data restore for Windows® XP, Windows Vista®, and Windows 7 Browse to and load the update package (.capsule file) you downloaded from the LaCie website. Enter your administrator username and password. By the way, the NAS has a password recovery system similar to many. Utilities CD-ROM including LaCie Network Assistant If you have more than one LaCie network storage device on your network, select your product from the list on the left. The included LaCie Network Assistant tool can help you find the NAS on your network. UPnP/DLNA compliant device for media streaming Leave it for 1 hour - after giving up rebooting a few times (both PC and Lacie NAS - just the 'blue-eye' button), leave. ![]() Latest versions of Windows® XP (SP2 and SP3), Windows Vista®, Windows 7/ Mac® OS X 10.5 or later Two things I've done that seem to fix it: Reboot the computer, which re-loads the Lacie Network Assistant (sometimes finds the named NAS sometimes it just. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |